Determination of the relative atomic mass of lithium

I set up the apparatus. Then I carried out the correct measurements of water and lithium. I weighed the lithium as well, however when I did this I removed as much of the oil as possible, but not all of it. This was then placed in a small container. The container with the lithium inside was then placed in a conical flask, upright. A bung was placed on top to ensure the collection of gas was successful. I shook the conical flask so the container fell on its side to allow the reaction to take place.

The gas produced was collected in a measuring cylinder.Section 2Apparatus> Conical flask> Burette> Clamp standProcedureI pipette 25cm3 of the solution from section 1, which was then placed into a conical flask. 5 drops of phenolphthalein indicator was added to the solution. Hydrochloric acid was placed in the burette, which was titrated.

Best services for writing your paper according to Trustpilot

Premium Partner
From $18.00 per page
4,8 / 5
4,80
Writers Experience
4,80
Delivery
4,90
Support
4,70
Price
Recommended Service
From $13.90 per page
4,6 / 5
4,70
Writers Experience
4,70
Delivery
4,60
Support
4,60
Price
From $20.00 per page
4,5 / 5
4,80
Writers Experience
4,50
Delivery
4,40
Support
4,10
Price
* All Partners were chosen among 50+ writing services by our Customer Satisfaction Team

I repeated the titration to ensure there was a fair test, these results were recorded.Health & safetyLithium metal is flammable and corrosive. Lithium reacts with water violently, creating a highly flammable gas Hydrogen.

When the lithium reacts with water it also forming lithium hydroxide solution, which is corrosive. Lithium metal also burns in air. So therefore when using the metal lithium take great care, as you will need to wear goggles. Lithium is stored in oil, so when removing the oil wear rubber gloves to stop the metal reacting with any excess water on the skin. Hydrochloric acid is corrosive, so careful use is needed as well as wearing goggles.ResultsSection 1It is assumed that 1 mole of gas occupies 24000cm3 at room temperature and pressure:2Li (s) + 2H2O (l) 2LiOH (aq) + H2 (g)Mass of lithium: 0.135gAmount of hydrogen gas collected: 222cm3Calculate the number of moles of H2:Deduce the number of moles of lithium:Relative atomic mass of lithium:Section 2Titration results:TitrationVolume of HCl (cm3)1.422.

41.23.41.3Average titration using 2 & 3:41.2 + 41.3 = 82.582.

5 / 2 = 41.25cm3LiOH (aq) + HCl (aq) LiCl (aq) + H2O (l)Number of moles of HCl used in titration:Number of moles of LiOH used in titration:(1:1, from equation)Number of moles of LiOH present in 100cm3 in solution:(Method 1)Relative atomic mass of lithium calculated:EvaluationWhen comparing my result with the actual relative atomic mass of lithium (6.94), I find that my result is higher than that of the actual relative atomic mass.

However I believe there are a few errors which affect the accuracy of my result. When removing the oil from the lithium you cannot remove all of it, this could effect the weight of the lithium. If you could remove all of the oil this would increase the accuracy of the results. Another error was that the experiment was not fully carried out under standard conditions of 100kPa and 298K. To gain more accuracy I could have measured the pressure and temperature.

Another error was that the tubing used was slightly permeable, which meant that H2 could escape to lower the volume of gas collected. To prevent this you could use a non-permeable tube, which would increase the accuracy of the results.